Intel and Dell recently agreed to provide me with a Dell PowerEdge M610 blade server for me to use in my lab, so I thought I’d take advantage of the opportunity and write-up a review. I’m going to go into further details about the blade server in the following blog post, but here are the high-level quick specs:
Category Archives: Dell – Dell EMC
Dell To Introduce A New Mini-Chassis for Blades?
It’s been a little quiet in the blade market place over the past few weeks, but I found some information that may peak some interests. Continue reading
Dell Announces Blade Refresh and NIC Partitioning (NPAR)
Dell announced today a refresh of the PowerEdge M910 blade server based on the Intel Xeon E7 processor. The M910 is a full-height blade that can hold 512GB of RAM across 32 DIMMs. The refreshed M910 blade server will also feature Dell’s FlexMem bridge that enables users to use all 32 DIMM slots with only 2 CPUs. You can read more about the M910 blade server in an earlier blog post of mine here.
According to the Dell press release issued today Continue reading
Intel Announces New Xeon 4 Socket CPU (E7); Dell, HP and IBM Slated to Refresh Blades
UPDATED 11:30 a.m. EST (4/6/11) – Intel announced today the next version of their 4 socket chipset, known as “E7”. Previously known with the codename of Westmere EX, the newly released Xeon 7600 will be rebranded as the Intel Xeon E7. Continue reading
4 Socket Blade Servers Density: Vendor Comparison (2011)
Revised with corrections 3/1/2011 10:29 a.m. (EST)
Almost a year ago, I wrote an article highlighting the 4 socket blade server offerings. At that time, the offerings were very slim, but over the past 11 months, that blog post has received the most hits, so I figured it’s time to revise the article. In today’s post, I’ll review the 4 socket Intel and AMD blade servers that are currently on the market. Yes, I know I’ll have to revise this again in a few weeks, but I’ll cross that bridge when I get to it. Continue reading
Blade Server Market Share Comparison – Q3 2009 vs Q3 2010
I was updating a slide deck that I use to compare blade server technologies for customers when I came across the IDC and Gartner data from Q3 of 2009. I was very surprised at what I found out, so today’s post takes a look back at 2009 and compares it to 2010. Continue reading
Dell Adds Multi Blade Chassis Management, But Wait – There's More
Dell recently notified me the latest version – ver 3.1 – of the Dell Chassis Management Controller (CMC) added multi-chassis management capability. In other words, you can have one IP address to manage multiple chassis. Now you may ask, so what? Other vendors have had this feature already, so what’s the big deal. Here’s what’s big about this announcement: Continue reading
Dell Announces Converged 10GbE Switch for M1000e
Updated 1/27/2011
Dell quietly announced the addition of a 10 Gigabit Ethernet (10GbE) switch module, known as the M8428-k. This blade module advertises 600 ns low-latency, wire-speed, 10GbE performance, Fibre Channel over Ethernet (FCoE) switching, and low-latency 8 Gb Fibre Channel (FC) switching and connectivity. Continue reading
Gartner Releases Magic Quadrant for Blade Servers
Technology analyst, Gartner, released their Magic Quadrant focused specifically on blade servers this week and the results were not very surprising. Continue reading
HP’s New 32GB DIMMs Too Expensive?
A reader recently commented on my article about HP’s new 32GB DIMM, “At $8039 per DIMM, HP can support 384GB in a BL460c at the cost of $96,000 per server just for the memory! If you filled just one rack with these servers, you would spend $6 million just for the memory. And the memory would run at a paltry 800MHz. Continue reading